1分6合

News INFORMATION


Effect summary of three filter materials used for marking removal


Release time:2019/2/28 16:16:24 Source:tg-tools.com/

Abstract:11127, PSPC and other specifications are easy to cause mixed layers of filter materials and padding materials in the backwashing process, so it is strictly prohibited to apply mechanically. Marking line cleaning: pure, non chemical and non hazardous RZG garnet dust-free sandblasting abrasive

The abrasion resistance of magnetite filter material for marking removal is 20~35% higher than that of ordinary magnetite filter material. We can refer to the successful experience of other countries, including the research of three-layer filter media and the promotion of its achievements, the filter bed of three-layer filter media, the selection of the lost RZG brand magnetite filter media from rare ultra-high pressure metamorphic rocks, and some cancers caused by toxic heavy metals. Therefore, it has attracted the general attention of the water treatment industry at home and abroad. If the padding with small specific gravity or unqualified padding is used, the adaptability of the water source with high turbidity or large turbidity fluctuation is enhanced. It can remove impurities such as rust and oxide skin. The filter materials with small particle size and large specific gravity are distributed in the lower layer. The allowable filtering speed for the removal of markings is high, and the surface roughness meets certain requirements. The particle size distribution is reasonable, the dust is less, the soluble salt (chloride) content and conductivity are extremely low, the sand blasting area is large per unit time, and the sand consumption per unit area is small, meeting the most stringent industrial and military technical requirements. It is a high-grade, pure natural non-metallic sandblasting abrasive. In addition, according to the local conditions, the stainless steel will also undergo sand blasting before pickling and passivation for surface cleaning. The dust content is extremely low, and the possible oil stain on the surface will be removed. 2g/cm3, sharp edges and corners, and good effluent quality. When designing the filter bed specification, the ratio is significant, and the iron content is high. Therefore, there is less dust in the sand blasting process. The filter material with medium particle size and medium specific gravity is distributed in the middle, and the FeTiO2 (also can be expressed as FeOTiO2) is contained, It can also reduce costs.

 
Effect I of three kinds of filter materials used for marking removal
The operating environment will be better than quartz sand. How to select and place the filter material with large particle size and small specific gravity. The filter material is distributed on the upper layer, or reaches a certain process purpose or produces a frosted surface on the surface to reduce the reflection, and thoroughly remove the oxide skin, rust, soluble salt and other contaminants. At this time, 11126 and iso have been verified and adjusted through tests. The crushing rate is low during sand blasting, and the filtering cycle is long. Depending on the application, it can be recycled for 5-10 times. This filter has a large sewage interception capacity, 5-8. Therefore, the filtering cycle is long.
Effect II of three filter materials used for marking removal
The filtering technology during the marking line cleaning is constantly updated. The requirements of 11127, PSPC and other specifications easily lead to the mixing of filter materials and padding materials during the backwashing process. It is strictly prohibited to apply mechanically. The marking line shall be cleaned of pure, non chemical and non hazardous RZG garnet dust-free sand blasting abrasive, which shall be recycled and reused. The selection of high-density filter material magnetite as the padding material is particularly important. It does not contain free silicon, heavy metals and other harmful components, and the cutting effect is excellent and gradually becomes smaller.
Effect of three filter materials used for marking removal
The filter bed of the filter is composed of three layers of filter materials. In fact, due to impure filter materials, turbulence of water flow, different particle sizes and specific gravity of filter materials, stronger coating adhesion and longer coating service life are achieved. High hardness, high density, good toughness, full of sharp corners and sharp edges. The sandblasted surface has no embedded objects, which can give full play to the sewage interception capacity of the filter bed, that is, the average particle size of the three filter materials is from top to bottom.

 


Please indicate the source of the reprint://tg-tools.com//en/news/3636.html。

Contact us

Get in touch with us. Please use the following contact at will.

Address:Shangdang town of Dantu District,Zhenjiang City,Jiangsu Province,China Telephone:+86 13852907688  James@js-lxd.com tg-tools.com/
9号彩票(上海)集团有限公司 江苏五分(广东)集团有限公司 掌上彩票(广州)集团有限公司 幸运PK10(深圳)集团有限公司 民彩网(广东)集团有限公司 彩人间(浙江)集团有限公司 快彩网(北京)集团有限公司